62 lines
3.1 KiB
Plaintext
62 lines
3.1 KiB
Plaintext
###############################################################################
|
|
# Firmware patch file
|
|
# If the value is not set then patch download is disabled.
|
|
FW_PATCH="/vendor/firmware/BCM20791B5_002.006.013.0011.0000_Generic_I2C_NCD_Unsigned_configdata.ncd"
|
|
|
|
###############################################################################
|
|
# Firmware pre-patch file (sent before the above patch file)
|
|
# If the value is not set then pre-patch is not used.
|
|
FW_PRE_PATCH=""
|
|
|
|
###############################################################################
|
|
# LPTD mode configuration
|
|
# byte[0] is the length of the remaining bytes in this value
|
|
# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
|
|
# byte[1] is the param id it should be set to B9.
|
|
# byte[2] is the length of the LPTD parameters
|
|
# byte[3] indicates if LPTD is enabled
|
|
# if set to 0, LPTD will be disabled (parameters will still be sent).
|
|
# byte[4-n] are the LPTD parameters.
|
|
# By default, LPTD is enabled and default settings are used.
|
|
# See nfc_hal_dm_cfg.c for defaults
|
|
LPTD_CFG={38:B9:36:01:00:FF:FF:08:00:00:00:A0:0F:40:00:00:12:02:10:00:00:00:2D:0B:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00:03:00:D0:07:00:00:08:07:00:00:C8:00:00:00:00:00:00:00}
|
|
|
|
###############################################################################
|
|
# Startup Configuration (256 bytes maximum)
|
|
#
|
|
# This adjusts the configuration to set the C2 parameter byte[1] to 00 (to
|
|
# discover all UICC).
|
|
#
|
|
NFA_DM_START_UP_CFG={51:CB:01:01:A5:01:01:CA:14:00:00:00:00:0E:F0:55:00:00:0F:00:00:00:00:00:00:00:00:00:00:B5:03:01:03:FF:C2:08:01:08:00:04:80:C3:C9:01:80:01:01:C9:03:03:0F:AB:5B:01:02:B2:04:E8:03:00:00:CF:02:02:08:B1:06:00:20:00:00:00:12:18:01:01:28:01:01:54:01:02}
|
|
|
|
###############################################################################
|
|
# Antenna Configuration - This data is used when setting 0xC8 config item
|
|
# at startup (before discovery is started). If not used, no value is sent.
|
|
#
|
|
# The settings for this value are documented here:
|
|
# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
|
|
# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
|
|
#
|
|
# The values marked as ?? should be tweaked per antenna or customer/app:
|
|
# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
|
|
# array[0] = 0x20 is length of the payload from array[1] to the end
|
|
# array[1] = 0xC8 is PREINIT_DSP_CFG
|
|
#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0A:03:30:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
|
|
|
|
###############################################################################
|
|
# Snooze Mode Settings
|
|
#
|
|
# By default snooze mode is enabled. Set SNOOZE_MODE_CFG byte[0] to 0
|
|
# to disable.
|
|
#
|
|
# If SNOOZE_MODE_CFG is not provided, the default settings are used:
|
|
# They are as follows:
|
|
# 8 Sleep Mode (0=Disabled 1=UART 8=SPI/I2C)
|
|
# 0 Idle Threshold Host
|
|
# 0 Idle Threshold HC
|
|
# 0 NFC Wake active mode (0=ActiveLow 1=ActiveHigh)
|
|
# 1 Host Wake active mode (0=ActiveLow 1=ActiveHigh)
|
|
#
|
|
#SNOOZE_MODE_CFG={08:00:00:00:01}
|
|
|