385 lines
8.0 KiB
Plaintext
385 lines
8.0 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Copyright (c) 2022 Rockchip Electronics Co., Ltd.
|
|
*
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "rk3562.dtsi"
|
|
#include "rk3562-evb.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/rockchip.h>
|
|
|
|
/ {
|
|
model = "Rockchip RK3562 TEST1 DDR3 V10 Board";
|
|
compatible = "rockchip,rk3562-test1-ddr3-v10", "rockchip,rk3562";
|
|
|
|
dc_12v: dc-12v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "dc_12v";
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-min-microvolt = <12000000>;
|
|
regulator-max-microvolt = <12000000>;
|
|
};
|
|
|
|
rk809_sound: rk809-sound {
|
|
status = "okay";
|
|
compatible = "rockchip,multicodecs-card";
|
|
rockchip,card-name = "rockchip-rk809";
|
|
hp-det-gpio = <&gpio3 RK_PC6 GPIO_ACTIVE_LOW>;
|
|
rockchip,format = "i2s";
|
|
rockchip,mclk-fs = <256>;
|
|
rockchip,cpu = <&sai2>;
|
|
rockchip,codec = <&rk809_codec>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&hp_det>;
|
|
};
|
|
|
|
sdio_pwrseq: sdio-pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
clocks = <&rk809 1>;
|
|
clock-names = "ext_clock";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wifi_enable_h>;
|
|
|
|
/*
|
|
* On the module itself this is one of these (depending
|
|
* on the actual card populated):
|
|
* - SDIO_RESET_L_WL_REG_ON
|
|
* - PDN (power down when low)
|
|
*/
|
|
post-power-on-delay-ms = <200>;
|
|
reset-gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
vcc5v0_sys: vcc5v0-sys {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc5v0_sys";
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
vin-supply = <&dc_12v>;
|
|
};
|
|
|
|
vcc5v0_usb: vcc5v0-usb {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc5v0_usb";
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
vin-supply = <&dc_12v>;
|
|
};
|
|
|
|
vcc5v0_usb_host: vcc5v0-usb-host {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc5v0_usb_host";
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
|
|
vin-supply = <&vcc5v0_usb>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usb_host_pwren>;
|
|
};
|
|
|
|
vcc5v0_usb_otg: vcc5v0-usb-otg {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc5v0_usb_otg";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
gpio = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
|
|
vin-supply = <&vcc5v0_usb>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usb_otg_pwren>;
|
|
};
|
|
|
|
vcc3v3_clk: vcc3v3-clk {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc3v3_clk";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&vcc5v0_sys>;
|
|
};
|
|
|
|
vcc3v3_sys: vcc-sys {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc3v3_sys";
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&dc_12v>;
|
|
};
|
|
|
|
vcc25_ddr: vcc25-ddr {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc25_ddr";
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-min-microvolt = <2500000>;
|
|
regulator-max-microvolt = <2500000>;
|
|
vin-supply = <&vcc3v3_sys>;
|
|
};
|
|
|
|
vdd_npu: vdd-npu {
|
|
compatible = "pwm-regulator";
|
|
pwms = <&pwm6 0 5000 1>;
|
|
regulator-name = "vdd_npu";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-init-microvolt = <900000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-settling-time-up-us = <250>;
|
|
pwm-supply = <&vcc5v0_sys>;
|
|
status = "okay";
|
|
};
|
|
|
|
wireless-wlan {
|
|
compatible = "wlan-platdata";
|
|
rockchip,grf = <&sys_grf>;
|
|
wifi_chip_type = "ap6275s";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wifi_host_wake_irq>;
|
|
WIFI,host_wake_irq = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
|
|
WIFI,poweren_gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
|
|
wireless-bluetooth {
|
|
compatible = "bluetooth-platdata";
|
|
clocks = <&rk809 1>;
|
|
clock-names = "ext_clock";
|
|
//wifi-bt-power-toggle;
|
|
uart_rts_gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default", "rts_gpio";
|
|
pinctrl-0 = <&uart1m0_rtsn>;
|
|
pinctrl-1 = <&uart1_gpios>;
|
|
BT,reset_gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
|
|
BT,wake_gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
|
|
BT,wake_host_irq = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&combphy_pu {
|
|
status = "okay";
|
|
};
|
|
|
|
&dsi {
|
|
status = "okay";
|
|
};
|
|
|
|
&dsi_in_vp0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&dsi_panel {
|
|
power-supply = <&vcc3v3_lcd_n>;
|
|
reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&lcd_rst_gpio>;
|
|
};
|
|
|
|
&gmac0 {
|
|
/* Use rgmii-rxid mode to disable rx delay inside Soc */
|
|
phy-mode = "rgmii-rxid";
|
|
clock_in_out = "output";
|
|
|
|
snps,reset-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
|
|
snps,reset-active-low;
|
|
/* Reset time is 20ms, 100ms for rtl8211f */
|
|
snps,reset-delays-us = <0 20000 100000>;
|
|
|
|
tx_delay = <0x3f>;
|
|
/* rx_delay = <0x3f>; */
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&rgmiim1_miim
|
|
&rgmiim1_tx_bus2
|
|
&rgmiim1_rx_bus2
|
|
&rgmiim1_rgmii_clk
|
|
&rgmiim1_rgmii_bus
|
|
ðm1_pins>;
|
|
|
|
phy-handle = <&rgmii_phy>;
|
|
status = "okay";
|
|
};
|
|
|
|
>1x {
|
|
compatible = "goodix,gt1x";
|
|
reg = <0x14>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&touch_gpio>;
|
|
goodix,rst-gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
|
|
goodix,irq-gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
|
|
/*
|
|
* power-supply should switche to vcc3v3_lcd1_n
|
|
* when mipi panel is connected to dsi1.
|
|
*/
|
|
power-supply = <&vcc3v3_lcd_n>;
|
|
};
|
|
|
|
&mdio0 {
|
|
rgmii_phy: phy@1 {
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
|
reg = <0x1>;
|
|
clocks = <&cru CLK_GMAC_ETH_OUT2IO>;
|
|
assigned-clocks = <&cru CLK_GMAC_ETH_OUT2IO>;
|
|
assigned-clock-rates = <25000000>;
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
headphone {
|
|
hp_det: hp-det {
|
|
rockchip,pins = <3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
|
|
lcd {
|
|
lcd_rst_gpio: lcd-rst-gpio {
|
|
rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
|
|
sdio-pwrseq {
|
|
wifi_enable_h: wifi-enable-h {
|
|
rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
|
|
touch {
|
|
touch_gpio: touch-gpio {
|
|
rockchip,pins =
|
|
<0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
|
|
<0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
|
|
usb {
|
|
usb_host_pwren: usb-host-pwren {
|
|
rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
|
|
usb_otg_pwren: usb-otg-pwren {
|
|
rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
|
|
wireless-wlan {
|
|
wifi_host_wake_irq: wifi-host-wake-irq {
|
|
rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_down>;
|
|
};
|
|
};
|
|
|
|
wireless-bluetooth {
|
|
uart1_gpios: uart1-gpios {
|
|
rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&route_dsi {
|
|
status = "okay";
|
|
};
|
|
|
|
&sai2 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2s2m1_lrck
|
|
&i2s2m1_sclk
|
|
&i2s2m1_sdi
|
|
&i2s2m1_sdo>;
|
|
};
|
|
|
|
&sdmmc0 {
|
|
no-sd;
|
|
no-mmc;
|
|
bus-width = <4>;
|
|
disable-wp;
|
|
cap-sd-highspeed;
|
|
cap-sdio-irq;
|
|
keep-power-in-suspend;
|
|
mmc-pwrseq = <&sdio_pwrseq>;
|
|
non-removable;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd>;
|
|
sd-uhs-sdr104;
|
|
status = "okay";
|
|
};
|
|
|
|
&sdmmc1 {
|
|
no-sdio;
|
|
no-mmc;
|
|
bus-width = <4>;
|
|
cap-mmc-highspeed;
|
|
cap-sd-highspeed;
|
|
disable-wp;
|
|
sd-uhs-sdr104;
|
|
vmmc-supply = <&vcc3v3_sd>;
|
|
vqmmc-supply = <&vccio_sd>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_clk &sdmmc1_cmd &sdmmc1_det>;
|
|
/* Should disable gmac0 and fix hardware if enabling sdmmc1 */
|
|
status = "disabled";
|
|
};
|
|
|
|
&pwm6 {
|
|
status = "okay";
|
|
};
|
|
|
|
&u2phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&u2phy_host {
|
|
status = "okay";
|
|
phy-supply = <&vcc5v0_usb_host>;
|
|
};
|
|
|
|
&u2phy_otg {
|
|
status = "okay";
|
|
vbus-supply = <&vcc5v0_usb_otg>;
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
|
|
};
|
|
|
|
&usb_host0_ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_host0_ohci {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbdrd30 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbdrd_dwc3 {
|
|
status = "okay";
|
|
dr_mode = "otg";
|
|
extcon = <&u2phy>;
|
|
};
|
|
|
|
&vcc3v3_lcd_n {
|
|
gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
&video_phy {
|
|
status = "okay";
|
|
};
|