152 lines
5.1 KiB
Plaintext
152 lines
5.1 KiB
Plaintext
Overview
|
|
--------
|
|
- BSC9131 is integrated device that targets Femto base station market.
|
|
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
|
|
technologies with MAPLE-B2F baseband acceleration processing elements.
|
|
- It's MAPLE disabled personality is called 9231.
|
|
|
|
The BSC9131 SoC includes the following function and features:
|
|
. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
|
|
L2 cache
|
|
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
|
|
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
|
|
Processing (MAPLE-B2F)
|
|
. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
|
|
Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
|
|
and CRC algorithms
|
|
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
|
|
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
|
|
operations
|
|
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
|
|
ECC, up to 400-MHz clock/800 MHz data rate
|
|
. Dedicated security engine featuring trusted boot
|
|
. DMA controller
|
|
. OCNDMA with four bidirectional channels
|
|
. Interfaces
|
|
. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
|
|
including IEEE 1588. v2 hardware support and virtualization (eTSEC)
|
|
. eTSEC 1 supports RGMII/RMII
|
|
. eTSEC 2 supports RGMII
|
|
. High-speed USB 2.0 host and device controller with ULPI interface
|
|
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
|
|
. Antenna interface controller (AIC), supporting three industry standard
|
|
JESD207/three custom ADI RF interfaces (two dual port and one single port)
|
|
and three MAXIM's MaxPHY serial interfaces
|
|
. ADI lanes support both full duplex FDD support and half duplex TDD support
|
|
. Universal Subscriber Identity Module (USIM) interface that facilitates
|
|
communication to SIM cards or Eurochip pre-paid phone cards
|
|
. TDM with one TDM port
|
|
. Two DUART, four eSPI, and two I2C controllers
|
|
. Integrated Flash memory controller (IFC)
|
|
. TDM with 256 channels
|
|
. GPIO
|
|
. Sixteen 32-bit timers
|
|
|
|
The e500 core subsystem within the Power Architecture consists of the following:
|
|
. 32-Kbyte L1 instruction cache
|
|
. 32-Kbyte L1 data cache
|
|
. 256-Kbyte L2 cache/L2 memory/L2 stash
|
|
. programmable interrupt controller (PIC)
|
|
. Debug support
|
|
. Timers
|
|
|
|
The SC3850 core subsystem consists of the following:
|
|
. 32 Kbyte 8-way level 1 instruction cache (L1 ICache)
|
|
. 32 Kbyte 8-way level 1 data cache (L1 DCache)
|
|
. 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory)
|
|
. Memory management unit (MMU)
|
|
. Enhanced programmable interrupt controller (EPIC)
|
|
. Debug and profiling unit (DPU)
|
|
. Two 32-bit timers
|
|
|
|
BSC9131RDB board Overview
|
|
-------------------------
|
|
1Gbyte DDR3 (on board DDR)
|
|
128Mbyte 2K page size NAND Flash
|
|
256 Kbit M24256 I2C EEPROM
|
|
128 Mbit SPI Flash memory
|
|
USB-ULPI
|
|
eTSEC1: Connected to RGMII PHY
|
|
eTSEC2: Connected to RGMII PHY
|
|
DUART interface: supports one UARTs up to 115200 bps for console display
|
|
USIM connector
|
|
|
|
Frequency Combinations Supported
|
|
--------------------------------
|
|
Core MHz/CCB MHz/DDR(MT/s)
|
|
1. 1000/500/800
|
|
2. 800/400/667
|
|
|
|
Boot Methods Supported
|
|
-----------------------
|
|
1. NAND Flash
|
|
2. SPI Flash
|
|
|
|
Default Boot Method
|
|
--------------------
|
|
NAND boot
|
|
|
|
Building U-Boot
|
|
--------------
|
|
To build the U-Boot for BSC9131RDB:
|
|
1. NAND Flash with sysclk 66MHz(J16 on RDB closed, default)
|
|
make BSC9131RDB_NAND
|
|
2. NAND Flash with sysclk 100MHz(J16 on RDB open)
|
|
make BSC9131RDB_NAND_SYSCLK100
|
|
3. SPI Flash with sysclk 66MHz(J16 on RDB closed, default)
|
|
make BSC9131RDB_SPIFLASH
|
|
4. SPI Flash with sysclk 100MHz(J16 on RDB open)
|
|
make BSC9131RDB_SPIFLASH_SYSCLK100
|
|
|
|
Memory map
|
|
-----------
|
|
0x0000_0000 0x7FFF_FFFF DDR 1G cacheable
|
|
0xA0000000 0xBFFFFFFF Shared DSP core L2/M2 space 512M
|
|
0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
|
|
0xC1F0_0000 0xC1F3_FFFF PA SRAM Region 0 256K
|
|
0xC1F8_0000 0xC1F9_FFFF PA SRAM Region 1 128K
|
|
0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
|
|
0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K
|
|
0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
|
|
0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
|
|
0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M
|
|
|
|
DDR Memory map
|
|
---------------
|
|
0x0000_0000 0x36FF_FFFF Memory passed onto Linux
|
|
0x3700_0000 0x37FF_FFFF PowerPC-DSP shared control area
|
|
0x3800_0000 0x4FFF_FFFF DSP Private area
|
|
|
|
Out of 880M, passed onto Linux, 1hugetlb page of 256M is reserved for
|
|
data communcation between PowerPC and DSP core.
|
|
Rest is PowerPC private area.
|
|
|
|
Flashing Images
|
|
---------------
|
|
To place a new U-Boot image in the NAND flash and then boot
|
|
with that new image temporarily, use this:
|
|
tftp 1000000 u-boot-nand.bin
|
|
nand erase 0 100000
|
|
nand write 1000000 0 100000
|
|
reset
|
|
|
|
Using the Device Tree Source File
|
|
---------------------------------
|
|
To create the DTB (Device Tree Binary) image file,
|
|
use a command similar to this:
|
|
|
|
dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb
|
|
|
|
Likely, that .dts file will come from here;
|
|
|
|
linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts
|
|
|
|
Booting Linux
|
|
-------------
|
|
Place a linux uImage in the TFTP disk area.
|
|
|
|
tftp 1000000 uImage
|
|
tftp 2000000 rootfs.ext2.gz.uboot
|
|
tftp c00000 bsc9131rdb.dtb
|
|
bootm 1000000 2000000 c00000
|