289 lines
9.2 KiB
Plaintext
289 lines
9.2 KiB
Plaintext
================================================================================
|
||
Board Information
|
||
================================================================================
|
||
|
||
Developed by HiSilicon, the board features the Hi3798C V200 with an
|
||
integrated quad-core 64-bit ARM Cortex A53 processor and high
|
||
performance Mali T720 GPU, making it capable of running any commercial
|
||
set-top solution based on Linux or Android. Its high performance
|
||
specification also supports a premium user experience with up to H.265
|
||
HEVC decoding of 4K video at 60 frames per second.
|
||
|
||
SOC Hisilicon Hi3798CV200
|
||
CPU Quad-core ARM Cortex-A53 64 bit
|
||
DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
|
||
USB Two USB 2.0 ports One USB 3.0 ports
|
||
CONSOLE USB-micro port for console support
|
||
ETHERNET 1 GBe Ethernet
|
||
PCIE One PCIe 2.0 interfaces
|
||
JTAG 8-Pin JTAG
|
||
EXPANSION INTERFACE Linaro 96Boards Low Speed Expansion slot
|
||
DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
|
||
WIFI 802.11AC 2*2 with Bluetooth
|
||
CONNECTORS One connector for Smart Card One connector for TSI
|
||
|
||
|
||
================================================================================
|
||
BUILD INSTRUCTIONS
|
||
================================================================================
|
||
|
||
Note of warning:
|
||
================
|
||
|
||
U-boot has a *strong* dependency with the l-loader and the arm trusted firmware
|
||
repositories.
|
||
|
||
The boot sequence is:
|
||
l-loader --> arm_trusted_firmware --> u-boot
|
||
|
||
U-Boot needs to be aware of the BL31 runtime location and size to avoid writing
|
||
over it. Currently, BL31 is being placed below the kernel text offset (check
|
||
poplar.c) but this could change in the future.
|
||
|
||
The current version of u-boot has been tested with:
|
||
- https://github.com/Linaro/poplar-l-loader.git
|
||
|
||
commit f0988698dcc5c08bd0a8f50aa0457e138a5f438c
|
||
Author: Alex Elder <elder@linaro.org>
|
||
Date: Fri Jun 16 08:57:59 2017 -0500
|
||
|
||
l-loader: use external memory region definitions
|
||
|
||
The ARM Trusted Firmware code now has a header file that collects
|
||
all the definitions for the memory regions used for its boot stages.
|
||
Include that file where needed, and use the definitions found therein
|
||
|
||
Signed-off-by: Alex Elder <elder@linaro.org>
|
||
|
||
|
||
- https://github.com/Linaro/poplar-arm-trusted-firmware.git
|
||
|
||
commit 6ac42dd3be13c99aa8ce29a15073e2f19d935f68
|
||
Author: Alex Elder <elder@linaro.org>
|
||
Date: Fri Jun 16 09:24:50 2017 -0500
|
||
|
||
poplar: define memory regions in a separate file
|
||
|
||
Separate the definitions for memory regions used for the BL stage
|
||
images and FIP into a new file. The "l-loader" image uses knowledge
|
||
of the sizes and locations of these memory regions, and it can now
|
||
include this (external) header to get these definitions, rather than
|
||
having to make coordinated changes to both code bases.
|
||
|
||
The new file has a complete set of definitions (more than may be
|
||
required by one or the other user). It also includes a summary of
|
||
how the boot process works, and how it uses these regions.
|
||
|
||
It should now be relatively easy to adjust the sizes and locations
|
||
of these memory regions, or to add to them (e.g. for TEE).
|
||
|
||
Signed-off-by: Alex Elder <elder@linaro.org>
|
||
|
||
|
||
Compile from source:
|
||
====================
|
||
|
||
Get all the sources
|
||
|
||
> mkdir -p ~/poplar/src ~/poplar/bin
|
||
> cd ~/poplar/src
|
||
> git clone https://github.com/Linaro/poplar-l-loader.git l-loader
|
||
> git clone https://github.com/Linaro/poplar-arm-trusted-firmware.git atf
|
||
> git clone https://github.com/Linaro/poplar-u-boot.git u-boot
|
||
|
||
Make sure you are using the correct branch on each one of these repositories.
|
||
The definition of "correct" might change over time (at this moment in time this
|
||
would be the "latest" branch).
|
||
|
||
Compile U-Boot:
|
||
===============
|
||
|
||
Prerequisite:
|
||
# sudo apt-get install device-tree-compiler
|
||
|
||
> cd ~/poplar/src/u-boot
|
||
> make CROSS_COMPILE=aarch64-linux-gnu- poplar_defconfig
|
||
> make CROSS_COMPILE=aarch64-linux-gnu-
|
||
> cp u-boot.bin ~/poplar/bin
|
||
|
||
Compile ARM Trusted Firmware (ATF):
|
||
===================================
|
||
|
||
> cd ~/poplar/src/atf
|
||
> make CROSS_COMPILE=aarch64-linux-gnu- all fip \
|
||
SPD=none BL33=~/poplar/bin/u-boot.bin DEBUG=1 PLAT=poplar
|
||
|
||
Copy resulting binaries
|
||
> cp build/hi3798cv200/debug/bl1.bin ~/poplar/src/l-loader/atf/
|
||
> cp build/hi3798cv200/debug/fip.bin ~/poplar/src/l-loader/atf/
|
||
|
||
Compile l-loader:
|
||
=================
|
||
|
||
> cd ~/poplar/src/l-loader
|
||
> make clean
|
||
> make CROSS_COMPILE=arm-linux-gnueabi-
|
||
|
||
Due to BootROM requiremets, rename l-loader.bin to fastboot.bin:
|
||
> cp l-loader.bin ~/poplar/bin/fastboot.bin
|
||
|
||
|
||
================================================================================
|
||
FLASH INSTRUCTIONS
|
||
================================================================================
|
||
|
||
Two methods:
|
||
|
||
Using USB debrick support:
|
||
Copy fastboot.bin to a FAT partition on the USB drive and reboot the
|
||
poplar board while pressing S3(usb_boot).
|
||
|
||
The system will execute the new u-boot and boot into a shell which you
|
||
can then use to write to eMMC.
|
||
|
||
Using U-BOOT from shell:
|
||
1) using AXIS usb ethernet dongle and tftp
|
||
2) using FAT formated USB drive
|
||
|
||
|
||
1. TFTP (USB ethernet dongle)
|
||
=============================
|
||
|
||
Plug a USB AXIS ethernet dongle on any of the USB2 ports on the Poplar board.
|
||
Copy fastboot.bin to your tftp server.
|
||
In u-boot make sure your network is properly setup.
|
||
|
||
Then
|
||
|
||
=> tftp 0x30000000 fastboot.bin
|
||
starting USB...
|
||
USB0: USB EHCI 1.00
|
||
scanning bus 0 for devices... 1 USB Device(s) found
|
||
USB1: USB EHCI 1.00
|
||
scanning bus 1 for devices... 3 USB Device(s) found
|
||
scanning usb for storage devices... 0 Storage Device(s) found
|
||
scanning usb for ethernet devices... 1 Ethernet Device(s) found
|
||
Waiting for Ethernet connection... done.
|
||
Using asx0 device
|
||
TFTP from server 192.168.1.4; our IP address is 192.168.1.10
|
||
Filename 'poplar/fastboot.bin'.
|
||
Load address: 0x30000000
|
||
Loading: #################################################################
|
||
#################################################################
|
||
###############################################################
|
||
2 MiB/s
|
||
done
|
||
Bytes transferred = 983040 (f0000 hex)
|
||
|
||
=> mmc write 0x30000000 0 0x780
|
||
|
||
MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
|
||
=> reset
|
||
|
||
|
||
2. USING USB FAT DRIVE
|
||
=======================
|
||
|
||
Copy fastboot.bin to any partition on a FAT32 formated usb flash drive.
|
||
Enter the uboot prompt
|
||
|
||
=> fatls usb 0:2
|
||
983040 fastboot.bin
|
||
|
||
1 file(s), 0 dir(s)
|
||
|
||
=> fatload usb 0:2 0x30000000 fastboot.bin
|
||
reading fastboot.bin
|
||
983040 bytes read in 44 ms (21.3 MiB/s)
|
||
|
||
=> mmc write 0x30000000 0 0x780
|
||
|
||
MMC write: dev # 0, block # 0, count 1920 ... 1920 blocks written: OK
|
||
|
||
|
||
================================================================================
|
||
BOOT TRACE
|
||
================================================================================
|
||
|
||
Bootrom start
|
||
Boot Media: eMMC
|
||
Decrypt auxiliary code ...OK
|
||
|
||
lsadc voltage min: 000000FE, max: 000000FF, aver: 000000FE, index: 00000000
|
||
|
||
Entry boot auxiliary code
|
||
|
||
Auxiliary code - v1.00
|
||
DDR code - V1.1.2 20160205
|
||
Build: Mar 24 2016 - 17:09:44
|
||
Reg Version: v134
|
||
Reg Time: 2016/03/18 09:44:55
|
||
Reg Name: hi3798cv2dmb_hi3798cv200_ddr3_2gbyte_8bitx4_4layers.reg
|
||
|
||
Boot auxiliary code success
|
||
Bootrom success
|
||
|
||
LOADER: Switched to aarch64 mode
|
||
LOADER: Entering ARM TRUSTED FIRMWARE
|
||
LOADER: CPU0 executes at 0x000ce000
|
||
|
||
INFO: BL1: 0xe1000 - 0xe7000 [size = 24576]
|
||
NOTICE: Booting Trusted Firmware
|
||
NOTICE: BL1: v1.3(debug):v1.3-372-g1ba9c60
|
||
NOTICE: BL1: Built : 17:51:33, Apr 30 2017
|
||
INFO: BL1: RAM 0xe1000 - 0xe7000
|
||
INFO: BL1: Loading BL2
|
||
INFO: Loading image id=1 at address 0xe9000
|
||
INFO: Image id=1 loaded at address 0xe9000, size = 0x5008
|
||
NOTICE: BL1: Booting BL2
|
||
INFO: Entry point address = 0xe9000
|
||
INFO: SPSR = 0x3c5
|
||
NOTICE: BL2: v1.3(debug):v1.3-372-g1ba9c60
|
||
NOTICE: BL2: Built : 17:51:33, Apr 30 2017
|
||
INFO: BL2: Loading BL31
|
||
INFO: Loading image id=3 at address 0x129000
|
||
INFO: Image id=3 loaded at address 0x129000, size = 0x8038
|
||
INFO: BL2: Loading BL33
|
||
INFO: Loading image id=5 at address 0x37000000
|
||
INFO: Image id=5 loaded at address 0x37000000, size = 0x58f17
|
||
NOTICE: BL1: Booting BL31
|
||
INFO: Entry point address = 0x129000
|
||
INFO: SPSR = 0x3cd
|
||
INFO: Boot bl33 from 0x37000000 for 364311 Bytes
|
||
NOTICE: BL31: v1.3(debug):v1.3-372-g1ba9c60
|
||
NOTICE: BL31: Built : 17:51:33, Apr 30 2017
|
||
INFO: BL31: Initializing runtime services
|
||
INFO: BL31: Preparing for EL3 exit to normal world
|
||
INFO: Entry point address = 0x37000000
|
||
INFO: SPSR = 0x3c9
|
||
|
||
|
||
U-Boot 2017.05-rc2-00130-gd2255b0 (Apr 30 2017 - 17:51:28 +0200)poplar
|
||
|
||
Model: HiSilicon Poplar Development Board
|
||
BOARD: Hisilicon HI3798cv200 Poplar
|
||
DRAM: 1 GiB
|
||
MMC: Hisilicon DWMMC: 0
|
||
In: serial@f8b00000
|
||
Out: serial@f8b00000
|
||
Err: serial@f8b00000
|
||
Net: Net Initialization Skipped
|
||
No ethernet found.
|
||
|
||
Hit any key to stop autoboot: 0
|
||
starting USB...
|
||
USB0: USB EHCI 1.00
|
||
scanning bus 0 for devices... 1 USB Device(s) found
|
||
USB1: USB EHCI 1.00
|
||
scanning bus 1 for devices... 4 USB Device(s) found
|
||
scanning usb for storage devices... 1 Storage Device(s) found
|
||
scanning usb for ethernet devices... 1 Ethernet Device(s) found
|
||
|
||
USB device 0:
|
||
Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade
|
||
Type: Removable Hard Disk
|
||
Capacity: 7632.0 MB = 7.4 GB (15630336 x 512)
|
||
... is now current device
|
||
Scanning usb 0:1...
|
||
=>
|