667 lines
22 KiB
C
667 lines
22 KiB
C
/*
|
|
* Copyright 2009 Extreme Engineering Solutions, Inc.
|
|
* Copyright 2007-2008 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* xpedite517x board configuration file
|
|
*/
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_XPEDITE5140 1 /* MPC8641HPCN board specific */
|
|
#define CONFIG_SYS_BOARD_NAME "XPedite5170"
|
|
#define CONFIG_SYS_FORM_3U_VPX 1
|
|
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
|
|
#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
|
|
#define CONFIG_BAT_RW 1 /* Use common BAT rw code */
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */
|
|
#define CONFIG_ALTIVEC 1
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xfff00000
|
|
|
|
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
|
|
#define CONFIG_PCIE1 1 /* PCIE controller 1 */
|
|
#define CONFIG_PCIE2 1 /* PCIE controller 2 */
|
|
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
|
|
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
|
|
|
|
/*
|
|
* DDR config
|
|
*/
|
|
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
|
|
#define CONFIG_DDR_SPD
|
|
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
|
#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */
|
|
#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */
|
|
#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
|
|
#define CONFIG_DDR_ECC
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
#define CONFIG_VERY_BIG_RAM
|
|
#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
|
|
|
|
/*
|
|
* virtual address to be used for temporary mappings. There
|
|
* should be 128k free at this VA.
|
|
*/
|
|
#define CONFIG_SYS_SCRATCH_VA 0xe0000000
|
|
|
|
#ifndef __ASSEMBLY__
|
|
extern unsigned long get_board_sys_clk(unsigned long dummy);
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC86xx */
|
|
|
|
/*
|
|
* L2CR setup
|
|
*/
|
|
#define CONFIG_SYS_L2
|
|
#define L2_INIT 0
|
|
#define L2_ENABLE (L2CR_L2E)
|
|
|
|
/*
|
|
* Base addresses -- Note these are effective addresses where the
|
|
* actual resources get mapped (not physical addresses)
|
|
*/
|
|
#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
|
|
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
|
|
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
|
|
#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
|
|
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
|
|
|
|
/*
|
|
* Diagnostics
|
|
*/
|
|
#define CONFIG_SYS_ALT_MEMTEST
|
|
#define CONFIG_SYS_MEMTEST_START 0x10000000
|
|
#define CONFIG_SYS_MEMTEST_END 0x20000000
|
|
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\
|
|
CONFIG_SYS_POST_I2C)
|
|
/* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
|
|
#define I2C_ADDR_IGNORE_LIST {0x50}
|
|
|
|
/*
|
|
* Memory map
|
|
* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
|
|
* 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
|
|
* 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable
|
|
* 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
|
|
* 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
|
|
* 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable
|
|
* 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
|
|
* 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
|
|
* 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
|
|
* 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
|
|
*/
|
|
|
|
#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3)
|
|
|
|
/*
|
|
* NAND flash configuration
|
|
*/
|
|
#define CONFIG_SYS_NAND_BASE 0xef800000
|
|
#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
|
|
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 2
|
|
#define CONFIG_NAND_ACTL
|
|
#define CONFIG_SYS_NAND_ACTL_ALE (1 << 14) /* C_LA14 */
|
|
#define CONFIG_SYS_NAND_ACTL_CLE (1 << 15) /* C_LA15 */
|
|
#define CONFIG_SYS_NAND_ACTL_NCE 0 /* NCE not controlled by ADDR */
|
|
#define CONFIG_SYS_NAND_ACTL_DELAY 25
|
|
#define CONFIG_JFFS2_NAND
|
|
|
|
/*
|
|
* NOR flash configuration
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0xf8000000
|
|
#define CONFIG_SYS_FLASH_BASE2 0xf0000000
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
#define CONFIG_FLASH_CFI_DRIVER
|
|
#define CONFIG_SYS_FLASH_CFI
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
|
|
#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff00000, 0xc0000}, \
|
|
{0xf7f00000, 0xc0000} }
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */
|
|
|
|
/*
|
|
* Chip select configuration
|
|
*/
|
|
/* NOR Flash 0 on CS0 */
|
|
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\
|
|
BR_PS_16 |\
|
|
BR_V)
|
|
#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB |\
|
|
OR_GPCM_CSNT |\
|
|
OR_GPCM_XACS |\
|
|
OR_GPCM_ACS_DIV2 |\
|
|
OR_GPCM_SCY_8 |\
|
|
OR_GPCM_TRLX |\
|
|
OR_GPCM_EHTR |\
|
|
OR_GPCM_EAD)
|
|
|
|
/* NOR Flash 1 on CS1 */
|
|
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 |\
|
|
BR_PS_16 |\
|
|
BR_V)
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
|
|
|
|
/* NAND flash on CS2 */
|
|
#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE |\
|
|
BR_PS_8 |\
|
|
BR_V)
|
|
#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB |\
|
|
OR_GPCM_BCTLD |\
|
|
OR_GPCM_CSNT |\
|
|
OR_GPCM_ACS_DIV4 |\
|
|
OR_GPCM_SCY_4 |\
|
|
OR_GPCM_TRLX |\
|
|
OR_GPCM_EHTR)
|
|
|
|
/* Optional NAND flash on CS3 */
|
|
#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 |\
|
|
BR_PS_8 |\
|
|
BR_V)
|
|
#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
|
|
|
|
/*
|
|
* Use L1 as initial stack
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_FSL
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 100000
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
|
#define CONFIG_SYS_FSL_I2C2_SPEED 100000
|
|
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
|
|
|
|
/* PEX8518 slave I2C interface */
|
|
#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
|
|
|
|
/* I2C DS1631 temperature sensor */
|
|
#define CONFIG_SYS_I2C_LM90_ADDR 0x4c
|
|
|
|
/* I2C EEPROM - AT24C128B */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
|
|
|
|
/* I2C RTC */
|
|
#define CONFIG_RTC_M41T11 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#define CONFIG_SYS_M41T11_BASE_YEAR 2000
|
|
|
|
/* GPIO */
|
|
#define CONFIG_PCA953X
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
|
|
#define CONFIG_SYS_I2C_PCA9553_ADDR 0x62
|
|
|
|
/*
|
|
* PU = pulled high, PD = pulled low
|
|
* I = input, O = output, IO = input/output
|
|
*/
|
|
/* PCA9557 @ 0x18*/
|
|
#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
|
|
#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */
|
|
#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
|
|
#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */
|
|
#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
|
|
#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */
|
|
|
|
/* PCA9557 @ 0x1c*/
|
|
#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */
|
|
#define CONFIG_SYS_PCA953X_PLUG_GPIO0 0x02 /* Samtec connector GPIO */
|
|
#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */
|
|
#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */
|
|
#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */
|
|
#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */
|
|
#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */
|
|
#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */
|
|
|
|
/* PCA9557 @ 0x1e*/
|
|
#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */
|
|
#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */
|
|
#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */
|
|
#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */
|
|
#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */
|
|
#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; VPX Geographical address parity */
|
|
#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; VPX P1 SYSCON */
|
|
|
|
/* PCA9557 @ 0x1f */
|
|
#define CONFIG_SYS_PCA953X_VPX_GPIO0 0x01 /* PU; VPX P15 GPIO */
|
|
#define CONFIG_SYS_PCA953X_VPX_GPIO1 0x02 /* PU; VPX P15 GPIO */
|
|
#define CONFIG_SYS_PCA953X_VPX_GPIO2 0x04 /* PU; VPX P15 GPIO */
|
|
#define CONFIG_SYS_PCA953X_VPX_GPIO3 0x08 /* PU; VPX P15 GPIO */
|
|
|
|
/*
|
|
* General PCI
|
|
* Memory space is mapped 1-1, but I/O space must start from 0.
|
|
*/
|
|
/* PCIE1 - PEX8518 */
|
|
#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
|
|
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
|
|
|
|
/* PCIE2 - VPX P1 */
|
|
#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS
|
|
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
|
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000
|
|
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */
|
|
|
|
/*
|
|
* Networking options
|
|
*/
|
|
#define CONFIG_TSEC_ENET /* tsec ethernet support */
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_ETHPRIME "eTSEC1"
|
|
|
|
#define CONFIG_TSEC1 1
|
|
#define CONFIG_TSEC1_NAME "eTSEC1"
|
|
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC1_PHY_ADDR 1
|
|
#define TSEC1_PHYIDX 0
|
|
#define CONFIG_HAS_ETH0
|
|
|
|
#define CONFIG_TSEC2 1
|
|
#define CONFIG_TSEC2_NAME "eTSEC2"
|
|
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
|
|
#define TSEC2_PHY_ADDR 2
|
|
#define TSEC2_PHYIDX 0
|
|
#define CONFIG_HAS_ETH1
|
|
|
|
/*
|
|
* BAT mappings
|
|
*/
|
|
#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT |\
|
|
BATU_BL_1M |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
|
|
#endif
|
|
|
|
/*
|
|
* BAT0 2G Cacheable, non-guarded
|
|
* 0x0000_0000 2G DDR
|
|
*/
|
|
#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U
|
|
|
|
/*
|
|
* BAT1 1G Cache-inhibited, guarded
|
|
* 0x8000_0000 1G PCI-Express 1 Memory
|
|
*/
|
|
#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_PHYS |\
|
|
BATU_BL_1G |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
|
|
|
|
/*
|
|
* BAT2 512M Cache-inhibited, guarded
|
|
* 0xc000_0000 512M PCI-Express 2 Memory
|
|
*/
|
|
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE2_MEM_PHYS |\
|
|
BATU_BL_512M |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCIE2_MEM_PHYS |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
|
|
|
|
/*
|
|
* BAT3 1M Cache-inhibited, guarded
|
|
* 0xe000_0000 1M CCSR
|
|
*/
|
|
#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR |\
|
|
BATU_BL_1M |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
|
|
|
|
/*
|
|
* BAT4 32M Cache-inhibited, guarded
|
|
* 0xe200_0000 16M PCI-Express 1 I/O
|
|
* 0xe300_0000 16M PCI-Express 2 I/0
|
|
*/
|
|
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_PHYS |\
|
|
BATU_BL_32M |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
|
|
|
|
/*
|
|
* BAT5 128K Cacheable, non-guarded
|
|
* 0xe400_1000 128K Init RAM for stack in the CPU DCache (no backing memory)
|
|
*/
|
|
#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR |\
|
|
BATL_PP_RW |\
|
|
BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR |\
|
|
BATU_BL_128K |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
|
|
#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
|
|
|
|
/*
|
|
* BAT6 256M Cache-inhibited, guarded
|
|
* 0xf000_0000 256M FLASH
|
|
*/
|
|
#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE2 |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE |\
|
|
BATU_BL_256M |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE |\
|
|
BATL_PP_RW |\
|
|
BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U
|
|
|
|
/* Map the last 1M of flash where we're running from reset */
|
|
#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE |\
|
|
BATU_BL_1M |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY |\
|
|
BATL_PP_RW |\
|
|
BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
|
|
|
|
/*
|
|
* BAT7 64M Cache-inhibited, guarded
|
|
* 0xe800_0000 64K NAND FLASH
|
|
* 0xe804_0000 128K DUART Registers
|
|
*/
|
|
#define CONFIG_SYS_DBAT7L (CONFIG_SYS_NAND_BASE |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT |\
|
|
BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT7U (CONFIG_SYS_NAND_BASE |\
|
|
BATU_BL_512K |\
|
|
BATU_VS |\
|
|
BATU_VP)
|
|
#define CONFIG_SYS_IBAT7L (CONFIG_SYS_NAND_BASE |\
|
|
BATL_PP_RW |\
|
|
BATL_CACHEINHIBIT)
|
|
#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */
|
|
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
|
|
#define CONFIG_PREBOOT /* enable preboot variable */
|
|
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 16 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
|
|
#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
|
|
#define CONFIG_ENV_SIZE 0x8000
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
|
|
/*
|
|
* Flash memory map:
|
|
* fffc0000 - ffffffff Pri FDT (256KB)
|
|
* fff80000 - fffbffff Pri U-Boot Environment (256 KB)
|
|
* fff00000 - fff7ffff Pri U-Boot (512 KB)
|
|
* fef00000 - ffefffff Pri OS image (16MB)
|
|
* f8000000 - feefffff Pri OS Use/Filesystem (111MB)
|
|
*
|
|
* f7fc0000 - f7ffffff Sec FDT (256KB)
|
|
* f7f80000 - f7fbffff Sec U-Boot Environment (256 KB)
|
|
* f7f00000 - f7f7ffff Sec U-Boot (512 KB)
|
|
* f6f00000 - f7efffff Sec OS image (16MB)
|
|
* f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
|
|
*/
|
|
#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff00000)
|
|
#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f00000)
|
|
#define CONFIG_FDT1_ENV_ADDR __stringify(0xfffc0000)
|
|
#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7fc0000)
|
|
#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
|
|
#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
|
|
|
|
#define CONFIG_PROG_UBOOT1 \
|
|
"$download_cmd $loadaddr $ubootfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
|
|
"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
|
|
"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
|
|
"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
|
|
"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_UBOOT2 \
|
|
"$download_cmd $loadaddr $ubootfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
|
|
"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
|
|
"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
|
|
"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
|
|
"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_BOOT_OS_NET \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"if test -n $fdtaddr; then " \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"bootm $osaddr - $fdtaddr; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"bootm $osaddr; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_OS1 \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
|
|
"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
|
|
"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo OS PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo OS PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_OS2 \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
|
|
"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
|
|
"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo OS PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo OS PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_FDT1 \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
|
|
"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
|
|
"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo FDT PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo FDT PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_FDT2 \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
|
|
"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
|
|
"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo FDT PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo FDT PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"autoload=yes\0" \
|
|
"download_cmd=tftp\0" \
|
|
"console_args=console=ttyS0,115200\0" \
|
|
"root_args=root=/dev/nfs rw\0" \
|
|
"misc_args=ip=on\0" \
|
|
"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
|
|
"bootfile=/home/user/file\0" \
|
|
"osfile=/home/user/board.uImage\0" \
|
|
"fdtfile=/home/user/board.dtb\0" \
|
|
"ubootfile=/home/user/u-boot.bin\0" \
|
|
"fdtaddr=0x1e00000\0" \
|
|
"osaddr=0x1000000\0" \
|
|
"loadaddr=0x1000000\0" \
|
|
"prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
|
|
"prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
|
|
"prog_os1="CONFIG_PROG_OS1"\0" \
|
|
"prog_os2="CONFIG_PROG_OS2"\0" \
|
|
"prog_fdt1="CONFIG_PROG_FDT1"\0" \
|
|
"prog_fdt2="CONFIG_PROG_FDT2"\0" \
|
|
"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
|
|
"bootcmd_flash1=run set_bootargs; " \
|
|
"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
|
|
"bootcmd_flash2=run set_bootargs; " \
|
|
"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
|
|
"bootcmd=run bootcmd_flash1\0"
|
|
#endif /* __CONFIG_H */
|